Differences

This shows you the differences between two versions of the page.

--- docs:man:installing_pld_linux_based_on_rescue_cd [2019-01-21 19:52] – [Kernel installation] arekm
+++ docs:man:installing_pld_linux_based_on_rescue_cd [2024-11-13 13:35] (current) – [Partition disk] anything there arekm
@@ Line 13: / Line 13: @@
 ===== Partition disk =====
-Use for example ''cfdisk'' to partition your destination disk. Usually root partition (/) and swap is enough. \\ :!: Write something more here :!:
+Use for example ''cfdisk'' to partition your destination disk. Usually root partition (/) and swap is enough.
+There are many ways you can partition your disk. Simple example below:
+  * cfdisk /dev/sdX (assuming fresh disk visible in system as sdX)
+  * choose GPT partition table
+  * create 10MB BIOS Boot partition
+  * create 1GB EFI System partition
+  * create Linux partition (or more partitions) for PLD
+\\ :!: Write something more here :!:
@@ Line 85: / Line 96: @@
 ===== Packages installation =====
+All packages are installed using **poldek** tool (it is a package manager for PLD).
 <file># rpm --root /pld --initdb
@@ Line 94: / Line 106: @@
 Packages which make sense to be installed:
-//udev pwdutils dhcpcd poldek vim geninitrd grub2 e2fsprogs//
+<file>udev pwdutils dhcpcd poldek vim geninitrd grub2 e2fsprogs tzdata glibc-localedb-all</file>
+If **xfs** filesystem was chosen then please install:
+<file>xfsprogs</file>
@@ Line 127: / Line 143: @@
 Note **Kernel driver in use: ata_piix** (alias scsi_hostadapter ata_piix)
+While at it, on actual installed PLD system (not needed on rescuecd), you can do the same for network card driver:
+<file>alias netdev-eth0 e1000e</file>
+(again **lspci -k** will help to choose correct one)
@@ Line 151: / Line 173: @@
 By default kernel installation also generates initrd based on mounted /proc, /sys, /dev files and configured fstab, modprobe.conf and few others configuration files. generated initrd (which by default is initramfs cpio image) is saved in /boot.
+----
+There are two initrd generators used in PLD: geninitrd and dracut. Choose one.
+=== geninitrd ===
 If something fails or you want to regenerate initrd manually you can do it using:
@@ Line 161: / Line 189: @@
 //-v// option causes geninitrd to write additional information, so you can see if proper kernel modules are being installed into initrd.
+=== dracut ===
+:!: Write something more here :!:
+----
+PLD supports systemd and non-systemd installations. In case of systemd installation you need to install package
+<file>systemd</file>
+package and setup default boot kernel cmdline option in grub/lilo. Add
+<file>init=/bin/systemd systemd.unit=graphical.target</file>
@@ Line 166: / Line 208: @@
 ===== Bootloader =====
+==== grub2 ====
-==== lilo ====
+Install grub2 on boot sector of disk:
+<file>grub-install /dev/sda</file>
+Generate configuration file for grub2:
+<file>update-grub</file>
+Resulting file is saved as **/boot/grub/grub.cfg**. Setting custom options for grub2 can be done in **/etc/sysconfig/grub** (then regenerate **grub.cfg** with **update-grub** command).
+==== lilo (deprecated) ====
 Edit **/pld/etc/lilo.conf**
@@ Line 186: / Line 240: @@
 </file>
+==== Advanced configuration ====
+Advanced lilo and grub configuration is described here: [[:Docs:man:Bootloader|../Bootloader]]
-==== grub ====
-Edit **/pld/boot/grub/menu.lst**
+===== udev =====
+\\ :!: Write something more here :!:
-<file>timeout 10
-title  pld
-root (hd0,1)
-kernel /boot/vmlinuz boot=/dev/hda
-initrd /boot/initrd
-</file>
-And execute
-<file># chroot /pld /sbin/grub
+===== User accounts =====
-</file>
-A Grub's shell will started. Let's make some changes:
-<file>grub> root (hd0,1)
+By default **root** account doesn't have any password set and by default that will prevent you from logging in. Setup root password
-grub> setup (hd0)
-grub> quit
-</file>
+<file>chroot /pld && passwd</file>
-==== Advanced configuration ====
+\\ :!: Write something more here :!:
-Advanced lilo and grub configuration is described here: [[:Docs:man:Bootloader|../Bootloader]]
+===== Finishing =====
+If manual network configuration was required for RescueCD then most liikely you need to repeat that [[docs:man:installing_pld_linux_based_on_rescue_cd#network_configuration_of_rescuecd|step]] on installed PLD system, too.
-===== udev =====
+Last step is umount all filesystems:
-\\ :!: Write something more here :!:
+<file>umount -R /pld</file>
+and reboot:
-===== User accounts =====
+<file>reboot</file>.
-\\ :!: Write something more here :!:
+If you find errors on this page or want to add anything to installation procedure please write to us at feedback / pld-linux.org.
-===== Finishing =====
 \\ :!: Write something more here :!: