This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
docs:man:installing_pld_linux_based_on_rescue_cd [2019-01-21 19:52] arekm [Kernel installation] |
docs:man:installing_pld_linux_based_on_rescue_cd [2019-01-21 20:15] arekm [Kernel installation] |
||
---|---|---|---|
Line 13: | Line 13: | ||
===== Partition disk ===== | ===== Partition disk ===== | ||
- | Use for example ''cfdisk'' to partition your destination disk. Usually root partition (/) and swap is enough. \\ :!: Write something more here :!: | + | Use for example ''cfdisk'' to partition your destination disk. Usually root partition (/) and swap is enough. |
+ | |||
+ | \\ :!: Write something more here :!: | ||
Line 85: | Line 87: | ||
===== Packages installation ===== | ===== Packages installation ===== | ||
+ | All packages are installed using **poldek** tool (it is a package manager for PLD). | ||
<file># rpm --root /pld --initdb | <file># rpm --root /pld --initdb | ||
Line 94: | Line 97: | ||
Packages which make sense to be installed: | Packages which make sense to be installed: | ||
- | //udev pwdutils dhcpcd poldek vim geninitrd grub2 e2fsprogs// | + | <file>udev pwdutils dhcpcd poldek vim geninitrd grub2 e2fsprogs tzdata glibc-localedb-all</file> |
+ | |||
+ | If **xfs** filesystem was chosen then please install: | ||
+ | |||
+ | <file>xfsprogs</file> | ||
Line 127: | Line 134: | ||
Note **Kernel driver in use: ata_piix** (alias scsi_hostadapter ata_piix) | Note **Kernel driver in use: ata_piix** (alias scsi_hostadapter ata_piix) | ||
+ | |||
+ | While at it, on actual installed PLD system (not needed on rescuecd), you can do the same for network card driver: | ||
+ | |||
+ | <file>alias netdev-eth0 e1000e</file> | ||
+ | |||
+ | (again **lspci -k** will help to choose correct one) | ||
Line 161: | Line 174: | ||
//-v// option causes geninitrd to write additional information, so you can see if proper kernel modules are being installed into initrd. | //-v// option causes geninitrd to write additional information, so you can see if proper kernel modules are being installed into initrd. | ||
+ | |||
+ | |||
+ | PLD supports systemd and non-systemd installations. In case of systemd installation you need to install package | ||
+ | |||
+ | <file>systemd</file> | ||
+ | |||
+ | package and setup default boot kernel cmdline option in grub/lilo. Add | ||
+ | |||
+ | <file>init=/bin/systemd systemd.unit=graphical.target</file> | ||
Line 166: | Line 188: | ||
===== Bootloader ===== | ===== Bootloader ===== | ||
+ | ==== grub2 ==== | ||
- | ==== lilo ==== | + | Install grub2 on boot sector of disk: |
+ | |||
+ | <file>grub-install /dev/sda</file> | ||
+ | |||
+ | Generate configuration file for grub2: | ||
+ | |||
+ | <file>update-grub</file> | ||
+ | |||
+ | Resulting file is saved as **/boot/grub/grub.cfg**. Setting custom options for grub2 can be done in **/etc/sysconfig/grub** (then regenerate **grub.cfg** with **update-grub** command). | ||
+ | |||
+ | |||
+ | ==== lilo (deprecated) ==== | ||
Edit **/pld/etc/lilo.conf** | Edit **/pld/etc/lilo.conf** | ||
Line 186: | Line 220: | ||
</file> | </file> | ||
+ | ==== Advanced configuration ==== | ||
+ | Advanced lilo and grub configuration is described here: [[:Docs:man:Bootloader|../Bootloader]] | ||
- | ==== grub ==== | ||
- | Edit **/pld/boot/grub/menu.lst** | ||
+ | ===== udev ===== | ||
+ | \\ :!: Write something more here :!: | ||
- | <file>timeout 10 | ||
- | title pld | ||
- | root (hd0,1) | ||
- | kernel /boot/vmlinuz boot=/dev/hda | ||
- | initrd /boot/initrd | ||
- | </file> | ||
- | And execute | ||
- | <file># chroot /pld /sbin/grub | + | ===== User accounts ===== |
- | </file> | + | |
- | A Grub's shell will started. Let's make some changes: | + | |
- | <file>grub> root (hd0,1) | + | By default **root** account doesn't have any password set and by default that will prevent you from logging in. Setup root password |
- | grub> setup (hd0) | + | |
- | grub> quit | + | |
- | </file> | + | |
+ | <file>chroot /pld && passwd</file> | ||
- | ==== Advanced configuration ==== | + | \\ :!: Write something more here :!: |
- | Advanced lilo and grub configuration is described here: [[:Docs:man:Bootloader|../Bootloader]] | + | |
+ | ===== Finishing ===== | ||
+ | If manual network configuration was required for RescueCD then most liikely you need to repeat that [[docs:man:installing_pld_linux_based_on_rescue_cd#network_configuration_of_rescuecd|step]] on installed PLD system, too. | ||
- | ===== udev ===== | + | Last step is umount all filesystems: |
- | \\ :!: Write something more here :!: | + | |
+ | <file>umount -R /pld</file> | ||
+ | and reboot: | ||
- | ===== User accounts ===== | + | <file>reboot</file>. |
- | \\ :!: Write something more here :!: | + | |
+ | |||
+ | If you find errors on this page or want to add anything to installation procedure please write to us at feedback / pld-linux.org. | ||
- | ===== Finishing ===== | ||
\\ :!: Write something more here :!: | \\ :!: Write something more here :!: | ||